Secure data centres with KentixONE
Access - Intrusion - Video surveillance - Environmental monitoring
You need only ONE system
Do you want to keep an uncomplicated eye on your data centre and all associated distributed infrastructures? With KentixONE, the IoT-based software and hardware platform for physical security technology, you can easily secure your entire building against intrusion and unauthorised access and monitor everything via video. All with just one system. KentixONE can be seamlessly integrated thanks to IoT technology, is uncomplicated to operate, always perfectly compatible and limitlessly expandable. This gives you full control and fends off up to 40 threats before damage and loss occur. All products are configured and operated via a uniform web interface. The software and data are yours.
Intrusion alarm
and room surveillance
Network radio based alarm centre
and sensors
With the Kentix Monitoring StarterSets you receive a complete package for a quick introduction to the innovative KentixONE monitoring technology. This allows you to monitor all critical physical hazards with just one system. All data from the MultiSensors is collected and evaluated in the AlarmManager or SiteManager. Use the quick configurator at the bottom of this page for product selection.
LAN (PoE)
FUNK
LTE-4G
SYSPORT
KentixONE
StarterSet SmartMonitoring
- Up to 100 devices (RADIO, LAN)
- Detected threats: up to 40
- Web-Server – KentixONE-GO
- SMS – E-MAIL – PUSH - VDS2465
- LDAP - SNMP - REST-API
- Room monitoring up to 2.000m²
Starter set for rack and room monitoring, expandable for distributed systems, up to 10,000 m²incl. LTE alarm center and integrated web interface / softwareMonitoring of:Temperature, humidity, climate control, smoldering fire / fire / fire gases (CO), intrusion / unauthorized access, access to unauthorized sub-areas (racks/cabinets), line loss / cable defects, failure of active system components, failure of services (HTTP,SMTP,VPN etc.), defective equipment fans, mains voltage failure, UPS defect failure, UPS remaining runtime and capacity.Possibility to connect up to 500 MultiSensors via radio and LANIntegrated LTE modem with slot for SIM card SNMP for integration into monitoring systemsAlarming via eMail (SSL), SMS or SNMP trap
LAN (PoE)
SYSPOPRT
KentixONE
MultiSensor-LAN with PoE (Black)
- KentixONE already integrated
- Integrated sensors: 8
- Monitored hazards: up to 19
- Stand-alone - Web server (HTTPS)
- E-MAIL - SNMP-V2/3
MultiSensor for comprehensive room monitoring of up to 20 hazards. Monitors an area of approx. 20-25m². Connection is via Ethernet with PoE (Class 1) and thus requires no further cabling.
Operation is possible as a stand-alone sensor with already integrated KentixONE software (HTTPS) or via a networked KentixONE system with AlarmManager or SiteManager. It is mounted on the ceiling using the supplied mounting bracket. Optionally, mounting in the IT rack is also possible with the 19" bracket (accessory).Integrated sensors: temperature, humidity, dew point, carbon monoxide sensor (CO), 360° PIR motion sensor, 3-axis G-sensor, digital input/outputs.Also ideal as an independent room sensor to complement network monitoring systems (PRTG, Nagios, CheckMK, etc) via SNMP-V2/3 or REST API. The sensor can also send alarm email in stand-alone mode.
SYSPORT
Leakagesensor KLS03
- Plug 'n Play connection
- Sensor sensitivity adjustable
- 5-fold cascadable
- Monitored for cable break
The leakage sensor is used to detect water leakage on the floor and is connected to an AlarmManager, MultiSensor or a SmartPDU directly to the "Kentix system socket". It continuously detects conductivity via multiple electrodes directly on the housing or additionally via a sensor cable.The sensor has an integrated point sensor with adjustable sensitivity. The versions with sensor cable (KLS03-ROPE-10/20) detect water in addition to the point sensor over the entire sensor cable length (10/20m). The sensitivity of the point sensor is 1-2ml water, the sensitivity of the sensor cable is approx. 10ml water over 20cm cable length.The leakage sensor can be cascaded up to 5 times and is therefore also suitable for large rooms.
Early fire detection
with thermal sensors
Detect fires before they start
with the Multisensor TI
With an integrated 1024 px thermal camera and 8 other sensors, the MultiSensor-TI ensures the early detection of more than 20 dangers in IT and technology rooms. Network-compatible with PoE and easy to configure thanks to integrated software (HTTPS). Can be integrated at any time thanks to SNMPv3 and REST API.Use the quick configurator at the bottom of this page for product selection.
LAN (PoE)
SYSPORT
KentixONE
MultiSensor-Thermal Image with 40° optics
- Integrated sensors: 9
- Monitored hazards: up to 20
- 4-factor early fire detection
- Stand-alone - Web server
- Email - SNMP alarm
MultiSensor with integrated 1024px thermal-cam sensor for 4-factor early fire detection and extented environmental monitoring.Full software on board with integrated web server (HTTPS), standalone operation or connection to Kentix AlarmManager-PRODetection angle: 40°Integrated sensors with monitoring of: Temperature, humidity, dew point, smoldering fire (CO), air quality, air-pressure, motion, acceleration-vibration (G), two external dry-contacts.Alarm notification via e-mail, SNMP traps (V2/3), web-hooks (REsT-API) or via AlarmManager SMS and PUSH.
LAN (PoE)
SYSPORT
KentixONE
MultiSensor-Thermal Image with 90° optics
- Integrated sensors: 9
- Monitored hazards: up to 20
- 4-factor early fire detection
- Stand-alone - Web server
- Email - SNMP alarm
MultiSensor with integrated 1024px thermal-cam sensor for 4-factor early fire detection and extented environmental monitoring.Full software on board with integrated web server (HTTPS), standalone operation or connection to Kentix AlarmManager-PRODetection angle: 90°Integrated sensors with monitoring of: Temperature, humidity, dew point, smoldering fire (CO), air quality, air-pressure, motion, acceleration-vibration (G), two external dry-contacts.Alarm notification via e-mail, SNMP traps (V2/3), web-hooks (REsT-API) or via AlarmManager SMS and PUSH.
Monitored area according to optics 40°or 90°
Area calculation
The Kentix MulitSensor mainapplication is room and system monitoring with 4-factor early fire detection. Which sensor version (40° or 90°) you choose depends largely on the mounting height and the application.
The 90° sensor is the right solution for 75% of all applications in the area of room and system monitoring. For the monitoring of sections the 40° sensor is the right choice.
LAN access control
Network-based RFID readers
for indoors and outdoors
Who has access to which room and when? With Kentix SmartAccess you have full (access) control: with different variants of radio-based locking components such as handles, knobs and wall readers as well as individual time-user profiles, you can set up an access solution exactly according to your needs in no time at all. Thanks to KentixONE, you always have an overview of all your rooms - at any time and also while on the move via app for smartphone or tablet. Use the quick configurator at the bottom of this page for product selection.
LAN (PoE)
PoE-SPLITTER
RFID
KentixONE
DoorLock-WA3-IP network reader (MIFARE® DESFire)
- KentixONE already integrated
- RFID & PIN
- Arm/disarm alarm buttons
- LED: RED-GREEN-YELLOW
- Integrated PoE Splitter 24VDC
- Protection class: IP54
StarterSet consisting of RFID wall reader with illuminated touch PIN keypad and AccessManager (SmartRelay) with Ethernet and PoE (10/100MBit), integrated web server (HTTPS) mit KentixONE, main-satellite mode for networking additional AccessManagers, reader mounting in switch box or surface mount, operating temperature -20°C to +60°C, protection class IP65, 2x relay 24VDC/1A, 2x digital input, expandable to a total of 2x RFID wall readers, scope of delivery: 1x wall reader with touch PIN keypad, 1x surface mount frame, 1x AccessManager (SmartRelay), 1x RFID key fob, 1x 3m SlimLine cable
LAN (PoE)
PoE-SPLITTER
RFID
KentixONE
DoorLock-WA6-IP network reader compact (MIFARE® DESFire)
- KentixONE already integrated
- RFID & PIN
- Arm/disarm alarm buttons
- LED: RED-GREEN-YELLOW
- Integrated PoE Splitter 24VDC
- Protection class: IP66
The frame reader is suitable e.g. for electric door openers, electric locks, electric door and gate drives or elevators. Due to its compact design, the reader is especially suitable for use with narrow metal profiles. Two-factor authentication is also possible. The AccessManager SmartRelay (PoE) forms the central unit with network connection. Management takes place centrally through the integrated web server.
LAN (PoE)
PoE-SPLITTER
RFID
KentixONE
DoorLock-WA3-IP outdoor (IP66) network reader (MIFARE® DESFire)
- KentixONE already integrated
- RFID
- LED: RED-GREEN
- Integrated PoE Splitter 24VDC
- Protection class: IP66
StarterSet DoorLock-WA as IP wall reader in weatherproof design (IP66) with RFID reader unit, Ethernet (10/100MBit) with PoE (Class 3), integrated web server with KentixONE (HTTPS), main-satellite mode for networking additional AccessManagers, operating temperature reader -30 to +70°C, 2 x relay 24VDC/1A, 2 x digital input, expandable to a total of 2 readers, scope of delivery: 1x wall reader (IP66), 1x network relay module (IP20), 1x RFID key fob, 1x 3m SlimLine cable
Current and voltage
monitoring
With the Kentix Smart PDU
in 40 U and 2 U
Intelligent, robust and calibrated: that was the formula for the development of our SmartPDU series. Together with long-standing data centre customers, we have developed a PDU that meets the essential requirements of robust and fail-safe power distribution.
We have thus fully concentrated on using the most proven components from the field of power distribution. The result is an ultra-robust PDU that meets all requirements for power measurement and monitoring and can be managed via state-of-the-art interfaces (SNMPv2/3, REST API). Use the quick configurator at the bottom of this page for product selection.
LAN(PoE)
KentixONE
MID-APPROVED
2x7.3kW
Dual SmartPDU 40U with 2x 24/C13 (IEC60320), 16A (A+B) with RCM
- Calibrated dual current measurement
- RCM differential current measurement
- Web-GUI, SNMP V2/3, Rest-API
- RFID Rack locking system connectable
- IEC Lock connector protection
- Network management, cascading
Kentix SmartPDUs are system components for the intelligent expansion of your rack infrastructure. All important sensors and interfaces for future-proof operation are already integrated.2x 24/C13 IEC sockets IEC lockable (IEC60320)Fuse protection 10A per group (C-type)2x mains connection IEC60309 plug 32A (BLUE) (L1/N/PE/6h)Cable connection 2m H05VV-F (4mm2)Measurement with MID approvalaccuracy class B (EN50470-3 MID)three counting rangesAC/DC differential current measurement (RCM)climate monitoring (Temp/Hum/Dew)optional early fire detection (CO)network connection RJ45 (PoE Ethernet)Frequency 45-54Hz (0.01Hz)Temperature range -10 to 50°CPower supply 230/400VACConnected load max 2x 7.2KVALine consumption max 40Wsize (LxWxH) 1770x78.1x62.5mmprotection class IP20
KentixONE
LAN(PoE)
MONITORING
MID-APPROVED
RCM
Dual SmartPDU 2HE with 2x 8/C13 (IEC60320), 16A (A+B) with RCM
- KentixONE already integrated
- Dual-PDU
- Calibrated total measurement
- RCM residual current measurement
- Temperature, humidity, dew point, vibration
- IEC Lock outlets
Kentix SmartPDUs are system components for the intelligent expansion of your rack infrastructure. All important sensors and interfaces for future-proof operation are already integrated.16xC13 IEC60320 IEC-Lock lockable socketsfuse protection 10A per group (C-type)mains connection 2xC20 (A+B) IEC plugmeasurement with MID approvalAccuracy class B (EN50470-3 MID)two counting ranges display illuminatedAC/DC differential current measurement (RCM)climate monitoring (Temp/Hum/Dew)network connection RJ45 (PoE Ethernet)frequency 45-54Hz (0.01Hz)temperature range -10 to 50°Cpower supply 230/400VACconnected load 4.6KVApower consumption approx. 3Wsize (LxWxH) 483x88x88mmprotection class IP20
LAN(PoE)
KentixONE
MID-APPROVED
7.3kW
SmartPDU 40U with 24/C13-6/C19 (IEC60320), 3-phase 32A with RCM
- Calibrated current measurement
- RCM differential current measurement
- Web-GUI, SNMP V2/3, Rest-API
- RFID Rack locking system connectable
- IEC Lock connector protection
- Network management, cascading
Kentix SmartPDUs are system components for the intelligent expansion of your rack infrastructure. All important sensors and interfaces for future-proof operation are already integrated.24xC13 and 6xC19 IEC sockets IEC-Lock lockable (IEC60320)protection 16A per group (C-type)mains connection IEC60309 connector 32A (ROT) (L1/L2/L3/N/PE/6h)cable connection H07RN-F (6mm2)measurement with MID approvalclass B accuracy (EN50470-3 MID)three counting rangesAC/DC differential current measurement (RCM)climate control (Temp. Hum / Dew)Network connection RJ45 (PoE Ethernet)Frequency 45-54Hz (0.01Hz)Temperature range -10 to 50 ° CPower supply 230VACPower consumption 22KVAPower consumption approx. 5WSize (LxWxH) 1770x78.1x62. 5mmprotection class IP20
Rack protection
With the network IT rack handle
with
ergonomic lifting lever and
online connection
The connection is made completely via patch cable. Up to 16 handles can be connected per Kentix AccessManager. A door contact can be connected to each IP rack handle, which safely monitors the closing and locking status of the rack door. Power is supplied via PoE and can therefore be easily integrated into the UPS power supply. When connected to the SmartPDU, it takes over the management of the handle and the monitoring of the door contacts. The only other hardware required is a central access manager.
Thanks to KentixONE, our locking solutions can be easily integrated into data center automation solutions via the REST API.
LAN (PoE)
RFID
KentixONE
DoorLock-RA4 Rack-Lift-Handle with PIN LEFT-TURN (MIFARE® DESFire)
- KentixONE already integrated
- RFID & PIN
- LED: RED-GREEN
- Up to 16 Lifthandles/SmartRelay
- Chassis: Metal-Plastic
IT cabinet handle (left turning) in robust metal-plastic design as folding lever handle. This means that the handle does not require a swivel range and enables ergonomic handling. The connection is made completely via patch cable. Up to 16 handles can be connected per Kentix SmartRelay. Any number of SmartRelays can be networked together. A reed contact can be connected to a distribution box to each IP rack handle to reliably monitor the closing and locking status of the rack door. The power supply is PoE and is therefore easily integrated into the UPS power supply.
TECH-INFO
Direction of rotation of the axis for lifting handles
The KXC-RA4 is available in two axis rotation directions (right/left). Since the lifting handle always performs the same movement, the gear unit or the axis rotation must be set according to the L/R door side.
Be sure to note the required direction of rotation of the axis when ordering. Easy to remember, the direction of rotation is always the same as the side of the door hinges.
For the direction of rotation, always look at the back of the door or back of the lever.
Your personal contact
Do you have questions or need advice on our products? I am at your disposal around the topics access, video and monitoring and look forward to hearing from you.
Miguel Marinho
Inside Sales Manager
Extention sensors for
external messages
For the connection, monitoring and visualization of
external fault messages from air conditioning and
UPS systems, fuses, etc.
The I/O expansion module connects to an AlarmManager-PRO and is used to connect external alarm messages. The communication takes place via Ethernet. Thus, the module can be mounted at any be mounted. The configuration is done in the web interface of the AlarmManager-PRO. 16 digital inputs (e.g. air conditioning, UPS system, external sensors, etc.) Up to 32 modules (max. 500 alarm inputs) can be operated on one AlarmManager-PRO.
LAN (POE)
Digital I/O-Module with 16-Inputs and Ethernet (PoE)
- 16 digital inputs
- connection of external alarm messages
- Integrated web server
- Power over Ethernet
The I/O expansion module connects to an AlarmManager/SiteManager and is used to connect external alarm messages. The communication takes place via Ethernet. Thus, the module can be mounted at any location. The configuration is done in the KentixONE..16 digital inputs (e.g. air conditioning, UPS system, external sensors, etc.)Up to 32 modules (max. 500 alarm inputs) can be operated on one AlarmManager-PRO.
LAN (POE)
Digital I/O-Module with 8-In-/Outputs and Ethernet (PoE)
- 8 digital in- and outputs
- connection of external alarm messages
- Integrated web server
- Power over Ethernet
The I/O expansion module connects to an AlarmManager/SiteManager and is used to connect external alarm messages to KentixONE. The communication takes place via Ethernet. Thus, the module can be mounted at any location. The configuration is done in the KentixONE.8 digital in- and outputs (e.g. air conditioning, UPS system, external sensors, etc.)Up to 32 modules (max. 500 alarm inputs) can be operated on one AlarmManager-PRO.
LAN (POE)
Analog-Module with 8-Inputs and 4 digital-outputs and Ethernet (PoE)
- 8 analog in- and 4 outputs
- connection of external alarm messages
- Integrated web server
- Power over Ethernet
The I/O expansion module connects to an AlarmManager/SiteManager and is used to connect external alarm messages to KentixONE. The communication takes place via Ethernet. Thus, the module can be mounted at any location. The configuration is done in the KentixONE.8 anlog inputs and 4 digital outputs (e.g. air conditioning, UPS system, external sensors, etc.)Up to 32 modules (max. 500 alarm inputs) can be operated on one AlarmManager-PRO.
Video surveillance
Network cameras
for inside and outdoors
The network cameras can be easily integrated into KentixONE and assigned to alarm zones or doors. The camera delivers full HD resolution and is ideal for indoor-outdoor surveillance thanks to its adjustable focal length (FOV 35-95°). In dark light conditions, it captures almost all crucial image details thanks to the LED infrared illuminator (up to 25m). The varifocal lens with remote zoom ensures easy configuration and installation of the network IP camera.
LAN(PoE)
5MP
5MP Sensor Outdoor (IP66) 360° Fisheye Network Camera with AI engine
- 5MP sensor with 2192x2192px
- 360° "Fish-Eye" lens
- Super dynamic range 102dB
- IR LED integrated
- Color night vision (0.019 to 0.3 lx)
- H.265 smart encoding
5MP fisheye images with up to 30 frames per second, network 100Mbit (PoE), Intelligent Auto (with AI Engine), Super Dynamic 120dB, Smart Coding (with AI Engine), IP66, IK10, 50J compliant, anti-condensation system, integrated IR-LED, NDDA compliant, content of delivery: 360° camera (white)
4MP
LAN (PoE)
IR-LED
Motor-Zoom
4MP Varifocal Lens Outdoor (IP66) Dome Network Camera
- 4MP sensor with 2688×1520px
- 2.5x built-in motorized zoom
- Super dynamic range 102dB
- IR LED integrated
- Color night vision (0.019 to 0.3 lx)
- H.265 smart encoding
- Corridor mode (90/270° image rotation
4MP sensor, 2688×1520 pixels image with up to 30fps, Built-in 2.5x motor zoom and motorized focus lens, Viewing angle H100°/V54°, Network 100Mbit (PoE) , Super dynamic range 102dB, Color night vision (0.019 to 0.3 lx), H.265 intelligent coding, Corridor mode (90 degree or 270 degree image rotation), Built-in IR LED, IP66 protection, NDDA compliant, ∅154x103mm, content of delivery: 5MP dome network camera (white).
